Regulations and Guidelines
Vessel man ufacturer, and /or installer of an EP A certified outboard, must meet minimum specifications for boat fuel systems established by:
- U.S. Environmental Protection Agency (EPA)
– 40 CFR 1045.112
– 40 CFR 1060
- U.S. Coast Guard (USCG)
– 33 CFR 183
- American Boat & Yacht Council (ABYC)
– Standard H-24
– Standard H-25.
Portable Fuel Tanks
If engine is equipped with a quick -disconnect fuel hose, you MUST disconnect the fuel hose from the engine and the fuel tank to prevent fuel leaks:
• Whenever the engine is NOT being used
• Whenever the engine is being trailered
• Whenever the engine is in storage.
NOTE: A small a mount o f fuel m ay be released when the fuel connector is disconnected. Store portable fuel tanks in well-ventilated areas, away from heat sources and open flames. Close the vent screw of the fuel tank cap, if equipped, to prevent escape of fuel or fuel vapors which could accidentally ignite. Do not allow disconnected fuel hoses to leak fuel.
Do not use port able fuel tanks for outboards larger than 1 15 HP. Inadequate fuel flow to high horsepower outboards can result in serious powerhead damage.
Fuel Flow Requirements
| 15 – 30 HP | 40 – 90 HP | 115 – 300 HP | |
|---|---|---|---|
| Fuel tank pickup tube | 1/4 in. (6.4 mm) min. ID | 5/16 in. (7.9 mm) min. ID | 3/8 in. (9.5 mm) min. ID |
| Fuel fittings | 5/32 in. (4.1 mm) min. ID | 1/4 in. (6.4 mm) min. ID | 9/32 in. (7.1 mm) min. ID |
| Fuel supply hoses | 1/4 in. (6.4 mm) min. ID | 3/8 in. (9.5 mm) min. ID | 3/8 in. (9.5 mm) min. ID |
| ALL MODELS | |
|---|---|
| Fuel tank pickup screen | 100 mesh, 304 grade stainless steel wire, 0.0045 in. wire diameter, 1 in. (25 mm) long |
| Antisiphon valve | 2.5 in. (63.5 mm) Hg maximum pressure drop at 20 gph (76 l/hr) flow |
| Remote fuel filter | 0.4 in. Hg maximum pressure drop at 20 gph (76 l/hr) flow, 150 in.² (1290 cm²) of filter area |
| Maximum fuel pump lift height | Fuel pump should not be located more than 30 in. (76.2 cm) above bottom of fuel tank |
Fuel Requirements
Gasoline is extremely flammable and highly explosive under certain conditions. Improper handling of fuel could result in property damage, serious injury or death.
Always turn off the outboard before fueling.
Never permit anyone other than an adult to refill the fuel tank.
Do not fill the fuel tank all the way to the top or fuel may overflow when it expands due to heating by the sun.
Remove portable fuel tanks from the boat before fueling.
Always wipe off any fuel spillage.
Do not smoke, allow op enflames or sparks, or use electrical devices such as
cellular phones in the vicinity of a fuel leak or while fueling.
Minimum Octane
Evinrude/Johnson outboards are certified to operate on unleaded automotive gasoline with an octane rating equal to or higher than:
87 (R+M)/2 AKI, or
90 RON
Use unleaded gasoline that contains methyl tertiary butyl ether (MTBE) ONLY if the MTBE con tent does not exceed 15% by volume.
Use alcohol-extended fuels ONLY if the alcohol content does not exceed:
10% ethanol by volume
5% methanol with 5% cosolvents by volume
When using alcohol-extended fuels, be aware of the following:
The b oat’s fuel system may have different requirements regarding the use of alcohol fuels. Refer to the boat’s owner guide.
Alcohol at tracts and holds moisture that can cause corrosion of metallic parts in the fuel system.
Alcohol blended fuel ca n cause engine performance problems.
All parts of the fuel system should be inspected frequently and replaced if signs of deterioration or fuel leakage are found. Inspect at least annually.
IMPORTANT: Always use fresh gasoline. Gasoline will oxidize, resulting in loss of octane and volatile compounds, as well as the production of gum and varnish deposits which can damage the out board.
Additives
IMPORTANT: The only fuel additives approved for use in Evinrude outboards are 2+4 fuel conditioner and Evinrude/Johnson Fuel System Cleaner. Use of other fuel additives can result in poor performance or engine damage.
Evinrude/Johnson 2+4 Fuel Conditioner will help prevent gum and varnish deposits from forming in fuel system components and will re move moisture from the fuel system. It can be used continuously and should be use d during any period when the outboard is not being operated on a regular basis. It s use will reduce spark plug fouling, fuel system icing, and fuel system component deterioration.
Evinrude/Johnson Fuel System Cleaner will help keep fuel injectors in optimal operating condition.
