Relay Testing
When the trim-UP button is pressed, the UP relay is energized and connects the blue trim motor wire to the battery positive (+) terminal. The green trim motor wire remains grounded. When the button is released, the blue trim moto r wire returns to a grounded position.
When the trim-DOWN button is pressed, the DOWN relay is energized and connects the green trim motor wire to the battery positive (+) terminal. The blue motor wire remains grounded. When the button is re leased, the green trim motor wire returns to a grounded position.
Refer to TILT/TRIM RELAY TEST on p. 106 for relay testing procedure.
Trim and Tilt Motor Current Draw Tests
Careful analysis of t he electric motor's current draw and trim/tilt unit operating speed aids evaluation of the electric motor a nd certain mechanical components.
Use a battery rated at 360 CCA (50 Ah) or higher that is in good condition and fully charged to per form this test.
IMPORTANT: Specifications are for static hydraulic test s. DO NOT attempt to perform the following tests while the boat is moving.
ELECTRICAL CIRCUIT TESTS Connect a 0 to 100 A DC ammeter in series between the battery side of the starter solenoid and the red lead to the trim/tilt relay module.


Observe ammeter and a stopwatch while running hydraulic unit through several complete cycles.
Compare test results to the values listed:
75 - 90 HP MODELS
| ModeFull Range UP | NormalCurrent Draw<30 A | Time in Seconds12-18 |
|---|---|---|
| Full Range DOWN | <30 A | <18 |
| Stall | <40 A | – |
40 - 60 HP MODELS
| ModeStall UP | NormalCurrent Draw11 to 16 Amps | Time in Seconds– |
|---|---|---|
| Stall DOWN | 16 to 22 Amps | – |
| Full Range UP | – | 13 to 19 |
| Full Range DOWN | – | 10 to 16 |
Test results include three basic possibilities:
A. Low current draw – Check for:
• Valves leaking
• Pump damaged
• O-rings leaking
• Manual release valve damaged
B. High current draw – Check for:
• Valves sticking
• Pump binding
• Motor binding
• Cylinder binding
C. Normal current draw, slow operating
speed – Check for:
• Manual release valve damaged
Trim and Tilt Motor No Load Test
IMPORTANT: Securely fasten motor in a suit able fixture before proceeding with this test.
Use a battery rated at 360 CCA (50 Ah) or higher that is in good condition and fully charged to per form this test.
Connect a 0 to 25 A ammeter in series with the battery positive (+) terminal, ammeter red le ad toward terminal.
Attach or hold a vibration or mechanical tachometer to the motor while performing this test.
Monitor motor RPM and current draw.

30957
The motor shaft must rotate clockwise, as viewed from the pump end, when positive (+) is applied to the blue le ad, a nd negative (– ) is connected to green lead.
The motor shaft must rotate counterclockwise, as viewed from the pump end, when positive (+) is applied to the green lead, and negative (–) is applied to the blue lead.

DR4238r
If test results vary, replace the motor.
Trim Gauge Test
STEP 1
Turn key switch ON. Using a voltmeter, check for
voltage between the trim gauge “I” and “G” terminals.
• If no voltage, check condition of instrument harness, key switch, and engine 20 A fuse.
• If voltage is shown, go to STEP 2.

DRC6245
STEP 2
Remove the white/t an lead from the trim gauge “S” terminal. With key switch ON, gauge should indicate full-trim DOWN position. Now connect a jumper wire between terminals “S” and “G.” Gauge should indicate full-trim UP position.
• If results are different, replace the trim gauge.
• If results agree, refer to Trim Sender Test.

DRC6246A
Trim Sender Test
IMPORTANT: To avoid immediate meter dam age, never apply an ohmmeter to an electrical circuit where voltage is present. Disconnect the 3-pin connector between the instrument harness and engine trim harness.
Connect an ohmmeter between the white/tan wire, terminal “C,” of the engine harness and a clean engine ground.
With the outboard fully DOW N, meter must show a reading above 80 ohms.
With the outboard fully UP , meter must show a reading below 10 ohms.
• If result s agree, refer to Trim Gauge Test on p. 351.
• If results are different, replace trim sender

DRC6247
