PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Service Manual 5008330_55 HP MFE Gearcase [Gearcase Removal And Installation]

Related Products:
Service Manual 5008330_55 HP MFE Gearcase [Gearcase Removal And Installation]
5008330
BRP Marine

GEAR CASE LEAK TEST

Drain lubricant before testing.

Use Gear case Pressure Tester, P/N 507977. Install lubricant drain/fill plug and seal, thread pressure test gauge fitting and seal in lubricant level hole.

Pressurize 3 to 6 psi (21 to 42 kPa).

If pressure gauge indicates leakage, submerge the gear case in water to determine source of leak. If the gauge does not indicate leakage, increase pressure to 16 to 18 psi (110 to 124 kPa). Check for leaks.

Make necessary repairs and repeat test.

Install Gear case Vacuum Tester, P/N 507982. Apply 3 to 5 in. of vacuum (76 to 127 mm) Hg. with pump.

If vacuum gauge indicates leakage, apply oil around suspected seal. If leak stops or oil is drawn in, seal is defective.

Repeat test, gear case must hold minimum of 15 in. vacuum (381 mm) Hg.

GEAR CASE REMOVAL AND INSTALLATION

Gear case Removal

To prevent accidental starting while servicing, twist and remove all spark plug leads. During service, the outboard may drop unexpectedly. Avoid personal injury; always support the outboard’s weight with a suitable hoist or the tilt support bracket during service.

Remove pin and washer from shift rod lever to release the lower shift rod.

  1. Shift rod screw

MRL MODELS

Note where the index mark on the gear case aligns with the index number of the adjustable trim tab so the trim tab can be installed in the same position. Remove the trim tab retaining screw and trim tab from the gear case.

  1. Trim tab 001996
  2. Trim tab retaining screw

Remove the forward screw with washer and recessed retaining screw.

  1. Forward screw

  2. Recessed screw

  3. Forward screw 001995 2. Recessed screw

MJRL MODELS

Remove the impeller housing and impeller assembly. Refer to IMPELLER SERVICE, MJRL MODELS on p. 236.
Remove the recessed retaining screw from the gear case.

  1. Screw

Remove nut and washer.

  1. Nut

ALL MODELS

Remove the four gear case retaining screws.

  1. Gear case retaining screws

Remove the gear case assembly from the exhaust housing, being careful not to bend the shift rod.

Gear case Installation

During service, the outboard may drop unexpectedly. Avoid personal injury; always support the outboard’s weight with a suitable hoist or the tilt support bracket during service.

Before installing gear case, shift rod adjustment MUST be checked. Refer to SHIFT ROD ADJUSTMENT on p. 244.

Coat the driveshaft splines with Moly Lube. DO NOT coat top surface of the driveshaft because lubricant may prevent seating of the driveshaft in the crankshaft.

Apply Adhesive 847 to the exhaust housing seal’s outer surface. Place the seal in the gear case exhaust cavity. Apply Triple-Guard grease to the seal’s inner surfaces.

  1. Exhaust housing seal

Slide the gear case into place, making sure:

  • Driveshaft engages the crankshaft—rotate fly wheel if necessary
  • Inner exhaust housing installs correctly
  • Shift rod does not turn and is positioned properly in shift shaft connection area.

Apply Triple-Guard grease to threads of the gear case retaining screws. Tighten the screws to a torque of:

• 3/8 in. screws – 18 to 20 ft. lbs. (24 to 27 N·m)
• 7/16 in. screw – 28 to 30 ft. lbs. (38 to 40 N·m)
• 5/16 in. screw – 10 to 12 ft. lbs. (13.5 to 16 N·m)

  1. 3/8 in. screws 001994

  1. 7/16 in. screw
  2. 5/16 in screw

MRL MODELS

Apply Triple-Guard grease to threads of the trim tab screw. Install and align the trim tab with the index marks noted prior to disassembly. Tighten the trim tab screw to a torque of 35 to 40 ft. lbs. (47 to 54 N·m). For adjustment, refer to Trim Tab
Adjustment (MRL) on p. 44.

  1. Trim tab screw 001996

MJRL MODELS

Install nut and washer. Tighten to a torque of 28 to 30 ft. lbs. (38 to 40 N·m).

  1. Nut

Install recessed retaining screw. Tighten to a torque of 10 to 12 ft. lbs. (13.5 to 16 N·m).

  1. Exhaust pipe
  2. Retaining screw

Install the impeller assembly and impeller housing. Refer to IMPELLER SERVICE, MJRL MODELS on p. 236.

Place the shift rod in the shift rod lever. Install the retaining pin and washer. Tighten pin to a torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

  1. Shift rod screw

To prevent loss of operator control, check for proper shifting operation and adjust, if necessary

IMPORTANT: During break-in period of a reassembled gear case, change the gear case lubricant between 10 to 20 hours of operation.

Share on social:

Related Products