PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Service Manual 5007211_Evinrude E-TEC 75-90 HP Trim And Tilt [Electrical Circuit Tests]

Related Products:
Service Manual 5007211_Evinrude E-TEC 75-90 HP Trim And Tilt [Electrical Circuit Tests]
5007211
BRP Marine

TROUBLESHOOTING

Use the following guidelines to check a single pis ton trim/tilt unit that is not working correctly.

Cylinder Leakdown:

  • Manual release valve seals

  • External leaks

No reverse lock:

  • External leaks

No operation, motor runs:

  • Manual release valve open

  • Fluid level low

  • Pump coupler

  • Hydraulic pump

No tilt down:

  • Manual release valve

  • Fluid level

Slow performance:

  • Manual release valve

  • Fluid level low

  • Mechanical binding

  • Electric motor

  • Hydraulic pump

Unit locked in tilt up:

  • Mechanical binding

  • Hydraulic pump

ELECTRICAL CIRCUIT TESTS

Relay Testing

When the trim-UP button is pressed, the UP relay is energized and connects the blue trim motor wire to the battery positive (+) terminal. The green trim motor wire remains grounded. When the button is released, the blue trim motor wire returns to a grounded position.

When the trim-DOWN button is pressed, the DOWN relay is energized and connects the green trim motor wire to the battery positive (+) terminal. The blue motor wire remains grounded. When the button is released, the green trim motor wire returns to a grounded position.

Refer to TILT/TRIM RELAY TEST on p. 138 for relay testing procedure.

Trim and Tilt Motor Current Draw Tests

Careful analysis of the electric motor's current draw and trim/tilt unit operating speed aids evaluation of the electric motor and certain mechanical components.

Use a battery rated at 360 CCA (50 Ah) or higher that is in good condition and fully charged to per form this test.

IMPORTANT: The specifications contained in the Performance Chart are for static hydraulic tests. DO NOT attempt to perform the following tests while the boat is moving.

Connect a 0 to 100 A DC ammeter in series between the battery side of the starter solenoid and the red lead to the trim/tilt relay module.

  1. Red lead

Observe ammeter and a stopwatch while running hydraulic unit through several complete cycles. Compare test results to the values listed:

Performance Chart

Mode Normal Current Draw Time in Seconds
Full Range UP <30 A 12-18
Full Range DOWN <30 A <18
Stall <40 A -

Test results include three basic possibilities:

A. Low current draw – Check for:

  • Valves leaking

  • Relief valve springs weak

  • Pump damaged

  • O-rings leaking

  • Check valves fouled or damaged

  • Manual release valve damaged

B. High current draw – Check for:

  • Pump binding

  • Motor binding

  • Cylinder binding

  • Valves sticking

C. Normal current draw, slow operating speed – Check for:

  • Impact valves damaged

  • Check valve or shuttle valve malfunctioning

  • Manual release valve damaged

Trim and Tilt Motor No Load Test

IMPORTANT: Securely fasten motor in a suit able fixture before proceeding with this test.

Use a battery rated at 360 CCA (50 Ah) or higher that is in good condition and fully charged to per form this test.

Connect a 0 to 50 A ammeter in series with the battery positive (+) terminal, ammeter red lead toward battery.

Attach or hold a vibration or mechanical tachometer to the motor while performing this test.

Monitor motor RPM and current draw.

The motor shaft must rotate clockwise, as viewed from the pump end, when positive (+) is applied to the blue lead, and negative (–) is connected to green lead.

The motor shaft must rotate counterclockwise, as viewed from the pump end, when positive (+) is applied to the green lead, and negative (–) is applied to the blue lead.

If test results vary, replace the motor.

Trim Gauge Test

STEP 1

Turn key switch ON. Using a voltmeter, check for voltage between the trim gauge “I” and “G” terminals.

  • If no voltage, check condition of instrument harness, key switch, and engine 20 A fuse.

  • If voltage, go to STEP 2.

STEP 2

Remove the white/tan lead from the trim gauge “S” terminal. With key switch ON, gauge should indicate full-trim DOWN position. Now connect a jumper wire between terminals “S” and “G.” Gauge should indicate full-trim UP position.

  • If results are different, replace the trim gauge.

  • If results agree, refer to Trim Sender Test.

Trim Sender Test

IMPORTANT: To avoid immediate meter dam age, never apply a multimeter to an electrical circuit where voltage is present.

Disconnect the 3-pin Deutsch connector between the instrument harness and engine trim harness. Connect an ohmmeter between the white/tan wire, terminal “C,” of the engine harness and a clean engine ground.

With the outboard fully DOWN, meter must show a reading above 80 Ω.

With the outboard fully UP, meter must show a reading below 10 Ω.

  • If results agree, refer to Trim Gauge Test on p. 290.

  • If results are different, replace trim sender.

REMOVAL AND INSTALLATION

Removal

Remove port lower engine cover and disconnect the trim/tilt connectors. Refer to Powerhead REMOVAL on p. 205.

Remove the rubber grommet from the blue/green trim/tilt cable connector.

Remove the terminals from the connector by using a suitable tool to depress the tab. While the tab is depressed, pull on the wire from the rear of the connector to release it from the connector.

Share on social:

Related Products