PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Rigging Information [Outboard Motor Troubleshooting] [2017]

Related Products:
Rigging Information [Outboard Motor Troubleshooting] [2017]
LIT-18616-03-61
Yamaha Marine

Troubleshooting procedure

  1. Before troubleshooting the outboard motor, check that fresh fuel of the specified type has been used.

  2. Check that all electrical connections are secure and free from corrosion, and that the battery is fully charged.

  3. Check the trouble code using the YDIS first, and then check the electronic control system following the trouble code chart.

  4. When a trouble code is detected, check the data logger of the engine ECM record graph as well.

  5. If a trouble code is not detected, check the power unit according to “Troubleshooting the power unit (trouble code not detected)” (4-18).

  6. Before using the YDIS to check the power unit, check the engine ECM circuit. See “Checking the engine ECM circuit” (5-19).

TIP:

  • When deleting the diagnosis record on the YDIS, make sure to check the time that the trouble codes were detected.
  • When checking the input voltage of a part, the coupler or connector must be disconnected. As a result, the engine ECM determines that the part is disconnected and a trouble code is detected. Therefore, make sure to delete the diagnosis record after checking the input voltage.
  • Since the main relay comes on for approximately 10 seconds after the engine start switch is turned to OFF, the power of the engine ECM cannot be turned off. Therefore, if the engine start switch is turned to ON within 10 seconds after it was turned to OFF, the trouble codes cannot be deleted.

Troubleshooting the power unit using the YDIS

  1. Use the trouble codes, displayed by the YDIS, to check each part according to the table of “Trouble code and checking step” (4-11).

  2. Delete the trouble codes after checking, repairing, or replacing a part and check that the trouble codes are not detected again. If the same trouble codes are detected, the engine ECM may be faulty.

  3. Check the items listed in the table. If all of the items are in good condition, delete the trouble codes, and then check the trouble codes again. If the same trouble codes are detected again, the engine ECM is faulty.

Trouble code table

✔ : Indicated
— : Not indicated

Code No. Item YDIS diagnosis YDIS diagnosis record
13 Pulser coil ✔ ✔
15 Engine temperature sensor ✔ ✔
17 Knock sensor ✔ ✔
19 Battery voltage ✔ ✔
23 Air temperature sensor ✔ ✔
24 Cam position sensor (EX) ✔ ✔
27 Water in fuel filter ✔ ✔
28 Shift position switch ✔ ✔
29 Air pressure sensor ✔ ✔
37 Intake air passage ✔ ✔
39 Oil pressure sensor ✔ ✔
44 Engine shut-off switch ✔ —
45 Shift cut-off switch ✔ ✔
46 Thermo switch ✔ ✔
59 Memory data — ✔
72 Cam position sensor ✔ ✔
74 OCV ✔ ✔
86 Immobilizer ✔ ✔
112, 113,114, 115,116, 117,119, 123,129, 138,141, 142,143, 144,145 ETV ✔ ✔
124, 125,126, 127,128 TPS ✔ ✔
131, 132,133, 134,135 APS ✔ ✔

Trouble code and checking step

—: Not applicable

Trouble code Item (Condition) Symptom Checking steps See page
13 Pulser coil (Irregular signal) “Check Engine” is displayed. Engine stops suddenly. Engine does not restart. Measure the pulser coil air gap. 7-1
13 Pulser coil (Irregular signal) “Check Engine” is displayed. Engine stops suddenly. Engine does not restart. Measure the pulser coil output peak voltage. 5-32
13 Pulser coil (Irregular signal) “Check Engine” is displayed. Engine stops suddenly. Engine does not restart. Measure the pulser coil resistance. 5-32
13 Pulser coil (Irregular signal) “Check Engine” is displayed. Engine stops suddenly. Engine does not restart. Check for wiring continuity between the pulser coil and the engine ECM. A-5
13 Pulser coil (Irregular signal) “Check Engine” is displayed. Engine stops suddenly. Engine does not restart. Check the protrusions on the flywheel magneto for damage 7-17
15 Engine temperature sensor (Out of specification) “Check Engine” is displayed. Degraded acceleration performance. Declining maximum engine speed. Measure the engine temperature sensor input voltage. 5-34
15 Engine temperature sensor (Out of specification) “Check Engine” is displayed. Degraded acceleration performance. Declining maximum engine speed. Measure the engine temperature sensor resistance. 5-34
15 Engine temperature sensor (Out of specification) “Check Engine” is displayed. Degraded acceleration performance. Declining maximum engine speed. Check for wiring continuity between the engine temperature sensor and the engine ECM. A-5
17 Knock sensor (Irregular signal) “Check Engine” is displayed. High engine idle speed. Measure the knock sensor resistance. 5-36
17 Knock sensor (Irregular signal) “Check Engine” is displayed. High engine idle speed. Check for wiring continuity between the knock sensor and the engine ECM. A-5
19 Battery voltage (Below specified voltage) Battery voltage and battery alert are displayed. Engine operates normally. Engine does not restart (depends on battery condition). Check the battery cable and terminals for proper connection. 10-4
19 Battery voltage (Below specified voltage) Battery voltage and battery alert are displayed. Engine operates normally. Engine does not restart (depends on battery condition). Measure the lighting coil output peak voltage. 5-28
19 Battery voltage (Below specified voltage) Battery voltage and battery alert are displayed. Engine operates normally. Engine does not restart (depends on battery condition). Measure the lighting coil resistance. 5-28
19 Battery voltage (Below specified voltage) Battery voltage and battery alert are displayed. Engine operates normally. Engine does not restart (depends on battery condition). Measure the Rectifier/Regulator/lsolator output voltage. 5-29
19 Battery voltage (Below specified voltage) Battery voltage and battery alert are displayed. Engine operates normally. Engine does not restart (depends on battery condition). Check the Rectifier/Regulator/Isolator for continuity. 5-29
Trouble code Item (Condition) Symptom Checking steps See page
23 Air temperature sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Check the intake air temperature using the YDIS. 5-34
23 Air temperature sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Check for wiring continuity between the intake air pressure/temperature sensor and the engine ECM. A-5
24 Cam position sensor(EX) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the cam position sensor input voltage. 5-22
24 Cam position sensor(EX) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the cam position sensor output voltage. 5-22
24 Cam position sensor(EX) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check for wiring continuity between the cam position sensor and the engine ECM. A-4
24 Cam position sensor(EX) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check the brim of the camshaft. 7-46
27 "Water in fuel filter (Water in fuel filter) “Water in fuel” is displayed. Alert buzzer comes on while the shift is in the N position. Check the fuel filter for water. -
27 "Water in fuel filter (Water in fuel filter) “Water in fuel” is displayed. Alert buzzer comes on while the shift is in the N position. Measure the water detection switch input voltage. 5-25
27 "Water in fuel filter (Water in fuel filter) “Water in fuel” is displayed. Alert buzzer comes on while the shift is in the N position. Check the water detection switch for continuity. 5-25
27 "Water in fuel filter (Water in fuel filter) “Water in fuel” is displayed. Alert buzzer comes on while the shift is in the N position. Check for wiring continuity between the water detection switch and the engine ECM. A-5
28 Shift position switch (Irregular signal) “Check Engine” is displayed. Engine operates normally. Check the gear shift operation. 10-6
28 Shift position switch (Irregular signal) “Check Engine” is displayed. Engine operates normally. Measure the shift position switch input voltage. 5-36
28 Shift position switch (Irregular signal) “Check Engine” is displayed. Engine operates normally. Check the shift position switch for continuity. 5-36
28 Shift position switch (Irregular signal) “Check Engine” is displayed. Engine operates normally. Check for wiring continuity between the shift position switch and the engine ECM. A-5
29 Air pressure sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Declining maximum engine speed. Measure the intake air pressure/ temperature sensor input voltage. 5-34
29 Air pressure sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Declining maximum engine speed. Check for wiring continuity between the intake air pressure/temperature sensor and the engine ECM. A-5
Trouble code Item (Condition) Symptom Checking steps See page
37 Intake air passage (Air leak) “Check Engine” is displayed. High engine idle speed. Impossible to shift-in (when the engine speed is more than 1500 r/min). Declining maximum engine speed. Check the gaskets of the intake manifold and ETV. 6-16
37 Intake air passage (Air leak) “Check Engine” is displayed. High engine idle speed. Impossible to shift-in (when the engine speed is more than 1500 r/min). Declining maximum engine speed. Check the hose between the vapor shut-off valve and the intake manifold. 6-13
37 Intake air passage (Air leak) “Check Engine” is displayed. High engine idle speed. Impossible to shift-in (when the engine speed is more than 1500 r/min). Declining maximum engine speed. Check the O-ring of the intake air pressure/temperature sensor. 6-23
39 Oil pressure sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Declining maximum engine speed. Check the oil pressure using the YDIS. 7-1
39 Oil pressure sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Declining maximum engine speed. Measure the oil pressure sensor input voltage. 5-24
39 Oil pressure sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Declining maximum engine speed. Measure the oil pressure sensor output voltage. 5-24
39 Oil pressure sensor (Out of specification) “Check Engine” is displayed. High engine idle speed. Declining maximum engine speed. Check for wiring continuity between the oil pressure sensor and the engine ECM. A-4
45 Shift cut-off switch (Irregular signal) “Check Engine” is displayed. Higher idle speed. Measure the shift cut-off switch input voltage. 5-36
45 Shift cut-off switch (Irregular signal) “Check Engine” is displayed. Higher idle speed. Measure the shift cut-off switch resistance. 5-36
45 Shift cut-off switch (Irregular signal) “Check Engine” is displayed. Higher idle speed. Check for wiring continuity between the shift cut-off switch and the engine ECM. A-5
59 Memory data (Irregular signal) “Check Engine” is displayed. Engine stalls. Replace the engine ECM. 7-29
72 Cam position sensor (IN) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the cam position sensor input voltage. 5-22
72 Cam position sensor (IN) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the cam position sensor output voltage. 5-22
72 Cam position sensor (IN) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check for wiring continuity between the cam position sensor and the engine ECM. A-4
72 Cam position sensor (IN) (Irregular signal) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check the brim of the camshaft 7-46
Trouble code Item (Condition) Symptom Checking steps See page
74 OCV (Irregular load current value) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check the OCV operation using the YDIS. 5-23
74 OCV (Irregular load current value) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the OCV input voltage. 5-23
74 OCV (Irregular load current value) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the OCV resistance. 5-23
74 OCV (Irregular load current value) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check for wiring continuity between the OCV and the main relay. A-4
74 OCV (Irregular load current value) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check for wiring continuity between the OCV and the engine ECM. A-4
74 OCV (Irregular load current value) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check the OCV filter. 10-15
86 Immobilizer (Communication error) “Check Engine” is displayed. Declining maximum engine speed. Check that Y-COP is connected properly. 3-21
86 Immobilizer (Communication error) “Check Engine” is displayed. Declining maximum engine speed. Measure the remote control receiver input voltage. -
86 Immobilizer (Communication error) “Check Engine” is displayed. Declining maximum engine speed. Check the Y-COP circuit. -
112 ETV system(Engine ECM internal circuit malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Replace the engine ECM. 7-29
113 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the TPS output voltage using the YDIS. 5-20
113 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
113 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the fuse. 5-5
113 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV motor relay. 5-20
115
116
ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
115
116
ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the throttle valve operation. 6-17
117 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
117 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the fuse. 5-5
117 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV motor relay. 5-20
117 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV. 6-17
Trouble code Item (Condition) Symptom Checking steps See page
119 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed.Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
123 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
123 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the fuse. 5-5
123 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV motor relay. 5-20
124
125
TPS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the TPS output voltage using the YDIS. 5-20
124
125
TPS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check the ETV circuit. A-4
126 TPS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the TPS output voltage using the YDIS. 5-20
126 TPS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the TPS input voltage. 5-20
126 TPS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
127
128
TPS (Out of specification) “Check Engine” is displayed. Degraded acceleration performance. Declining maximum engine speed. Measure the TPS output voltage using the YDIS. 5-20
127
128
TPS (Out of specification) “Check Engine” is displayed. Degraded acceleration performance. Declining maximum engine speed. Check the ETV circuit. A-4
129 ETV system (Engine ECM internal circuit malfunction) “Check Engine” is displayed. Degraded acceleration performance. Declining maximum engine speed. Replace the engine ECM. 7-29
131
132
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the APS output voltage using the YDIS. 5-21
131
132
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the APS input voltage. 5-21
131
132
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Measure the APS resistance. 5-21
131
132
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed. Check the APS circuit. A-4
Trouble code Item (Condition) Symptom Checking steps See page
133
134
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed Measure the APS output voltage using the YDIS. 5-21
133
134
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed Measure the APS input voltage. 5-21
133
134
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed Measure the APS resistance 5-21
133
134
APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Degraded acceleration performance. Declining maximum engine speed Check the APS circuit. A-4
135 APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the APS output voltage using the YDIS. 5-21
135 APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the APS input voltage. 5-21
135 APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the APS resistance. 5-21
135 APS (Out of specification) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the APS circuit. A-4
138 ETV system (Engine ECM internal circuit malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Replace the engine ECM. 7-29
141 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the ETV circuit. A-4
142 ETV system (Throttle valve malfunction) “Check Engine” is displayed. Declining maximum engine speed. Check the throttle valve operation. 6-17
142 ETV system (Throttle valve malfunction) “Check Engine” is displayed. Declining maximum engine speed. Replace the ETV. 6-17
143 ETV system (Engine ECM internal circuit malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Replace the engine ECM. 7-29
Trouble code Item (Condition) Symptom Checking steps See page
144 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the battery cable and terminals for proper connection. 10-4
144 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the fuse. 5-5
144 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the lighting coil output peak voltage. 5-28
144 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the lighting coil resistance. 5-28
144 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Measure the Rectifier/Regulator/lsolator output peak voltage. 5-29
144 ETV system (Throttle valve malfunction) “Check Engine” is displayed. High engine idle speed. Throttle does not operate. Engine speed is set at approximately 1500 r/min. Check the Rectifier/Regulator/Isolator for continuity. 5-29
145 ETV system (Throttle valve malfunction) High engine idle speed. Check that other trouble codes (112-144) are detected. 4-9
145 ETV system (Throttle valve malfunction) High engine idle speed. Check the throttle valve operation. 6-17

Troubleshooting the power unit (trouble code not detected)

Troubleshooting consists of the following 3 items:
Symptom 1: Specific trouble conditions
Symptom 2: Trouble conditions of an area or individual part
Cause: Trouble causes of symptom 2
—: Not applicable

Symptom 1: Engine does not crank.

Symptom 2 Cause Checking steps See page
Starter motor does not operate Gear shift not in the N position Set the gear shift to the N position. 10-6
Starter motor does not operate Blown fuse Check the fuse. 5-5
Starter motor does not operate Starter relay malfunction Check the starter relay. 5-37
Starter motor does not operate Engine start switch malfunction Check the engine start switch. 5-38
Starter motor does not operate Neutral switch malfunction Check the neutral switch. -
Starter motor does not operate Short, open, or loose connection in starter motor circuit Measure the starter relay input voltage. 5-34
Starter motor does not operate Short, open, or loose connection in starter motor circuit Check the wire harness for continuity. A-6
Starter motor does not operate Starter motor malfunction Disassemble and check the starter motor. 5-41
Starter motor operates, but the engine does not crank Stuck piston or crankshaft Disassemble and check the power unit. 7-87
Starter motor operates, but the engine does not crank Stuck drive shaft Check the drive shaft bushing. 9-17
9-32
Starter motor operates, but the engine does not crank Stuck drive shaft Disassemble and check the lower unit. 8-22

Symptom 1: Engine will not start (engine cranks).

Symptom 2 Cause Checking steps See page
Engine ECM does not operate Blown fuse Check the fuse. 5-5
Engine ECM does not operate Main relay malfunction Check the main relay. 5-18
Engine ECM does not operate Short, open, or loose connection in the engine ECM circuit Check for wire harness continuity between the main relay and the engine ECM. 5-19
Engine ECM does not operate Short, open, or loose connection in the engine ECM circuit Check for continuity between the engine ECM and ground. 5-19
Symptom 2 Cause Checking steps See page
Spark plug does not produce a spark (all cylinders) Pulser coil malfunction Measure the pulser coil output peak voltage. 5-32
Spark plug does not produce a spark (all cylinders) Pulser coil malfunction Measure the pulser coil resistance. 5-32
Spark plug does not produce a spark (all cylinders) Short, open, or loose connection in the pulser coil circuit Check for wire harness continuity between the pulser coil and the engine ECM. A-5
Spark plug does not produce a spark (all cylinders) Y-COP is locked. Unlock Y-COP. -
Fuel not supplied (all cylinders) - Measure the fuel pressure 6-1
Fuel not supplied (all cylinders) Pinched or kinked fuel hose Check the fuel hose. 2-27
Fuel not supplied (all cylinders) Fuel leakage Check the fuel line for leakage. 2-27
Fuel not supplied (all cylinders) Clogged fuel filter element Check the fuel filter element for dirt and obstructions. 6-7
Fuel not supplied (all cylinders) Blown fuse Check the fuse. 5-5
Fuel not supplied (all cylinders) High-pressure fuel pump malfunction Check the high-pressure fuel pump operation using the YDIS. 5-26
Fuel not supplied (all cylinders) High-pressure fuel pump malfunction Measure the high-pressure fuel pump resistance. 5-26
Fuel not supplied (all cylinders) Short, open, or loose connection in high-pressure fuel pump circuit Check the high-pressure fuel pump input voltage. 5-26
Fuel not supplied (all cylinders) Short, open, or loose connection in high-pressure fuel pump circuit Check for wiring continuity between the high-pressure fuel pump and the engine ECM. A-5
Fuel not supplied (all cylinders) Short, open, or loose connection in high-pressure fuel pump circuit Check for wiring continuity between the high-pressure fuel pump and the high-pressure fuel pump relay. A-5
Fuel not supplied (all cylinders) High-pressure fuel pump relay malfunction Check the high-pressure fuel pump relay. 5-27
Fuel not supplied (all cylinders) Short, open, or loose connection in low-pressure fuel pump circuit Check the low-pressure fuel pump input voltage. 5-26
Fuel not supplied (all cylinders) Short, open, or loose connection in low-pressure fuel pump circuit Check for wiring continuity between the low-pressure fuel pump and the engine ECM. A-5
Fuel not supplied (all cylinders) Short, open, or loose connection in low-pressure fuel pump circuit Check for wiring continuity between the low-pressure fuel pump and the main relay. A-5
Fuel not supplied (all cylinders) Low-pressure fuel pump malfunction Check the low-pressure fuel pump resistance 5-26
Fuel not supplied (all cylinders) Open check valve Check the check valve. 6-37
Symptom 2 Cause Checking steps See page
Compression pressure is low — Measure the compression pressure. 7-1
Compression pressure is low Improper valve timing Check the valve timing. 7-22
Compression pressure is low Improper valve timing Check the timing belt. 7-22
Compression pressure is low Compression leakage Check the valve for bends and sticking. 7-58
Compression pressure is low Compression leakage Check the piston and piston rings for damage. 7-87
Compression pressure is low Compression leakage Check the cylinder for scratches. 7-91

Symptom 1: Unstable engine idle speed, poor acceleration, poor performance, or limited engine speed.

Symptom 2 Cause Checking steps See page
Spark plug does not produce a spark (some cylinders) Spark plug malfunction Check the ignition spark. 5-32
Spark plug does not produce a spark (some cylinders) Spark plug malfunction Check the spark plug. 7-35
Spark plug does not produce a spark (some cylinders) Short, open, or loose connection in ignition coil circuit Measure the ignition coil input voltage. 5-32
Spark plug does not produce a spark (some cylinders) Short, open, or loose connection in ignition coil circuit Check for wiring continuity between the ignition coil and the engine ECM. A-5
Spark plug does not produce a spark (some cylinders) Short, open, or loose connection in ignition coil circuit Check for wiring continuity between the ignition coil and the main relay. A-5
Spark plug does not produce a spark (some cylinders) Ignition coil malfunction Exchange the ignition coil with a different one, and then check the ignition spark. 5-32
Spark plug does not produce a spark (some cylinders) Engine ECM malfunction Replace the engine ECM. 7-29
Fuel pressure is low — Measure the fuel pressure. 6-1
Fuel pressure is low Fuel leakage Check for fuel leakage. 2-27
Fuel pressure is low Pressure regulator malfunction Check the pressure regulator. 6-2
Fuel pressure is low Clogged fuel filter Check the fuel filter for dirt and obstructions. 6-7
Fuel pressure is low High-pressure fuel pump malfunction Measure the high-pressure fuel pump resistance. 5-26
Fuel pressure is low Open check valve Check the check valve. 6-37
Symptom 2 Cause Checking steps See page
Fuel not supplied (some cylinders) Fuel injector malfunction Check the fuel injector operation using the YDIS. 5-25
Fuel not supplied (some cylinders) Fuel injector malfunction Measure the fuel injector resistance. 5-25
Fuel not supplied (some cylinders) Short, open, or loose connection in fuel injector circuit Measure the fuel injector input voltage. 5-25
Fuel not supplied (some cylinders) Short, open, or loose connection in fuel injector circuit Check for wiring continuity between the fuel injector and the main relay A-5
Fuel not supplied (some cylinders) Short, open, or loose connection in fuel injector circuit Check for wiring continuity between the fuel injector and the engine ECM. A-5
Fuel not supplied (some cylinders) Clogged fuel injector Replace the fuel injector. 6-19
Fuel not supplied (some cylinders) Engine ECM malfunction Replace the engine ECM. 7-29
Compression pressure is low — Measure the compression pressure. 7-1
Compression pressure is low Improper valve timing Check the valve timing. 7-22
Compression pressure is low Improper valve timing Check the timing belt. 7-22
Compression pressure is low Compression leakage Check the valve for bends and sticking. 7-58
Compression pressure is low Compression leakage Check the piston and piston rings for damage. 7-87
Compression pressure is low Compression leakage Check the cylinder for scratches. 7-91

Symptom 1: High engine idle speed

Symptom 2 Cause Checking steps See page
- Air leakage (ETV-cylinder head) Check the gaskets of the intake manifolds, intake air pressure/temperature sensor, and ETV 6-23
6-16

Symptom 1: Engine stalls, unstable engine idle speed, or poor acceleration.

Symptom 2 Cause Checking steps See page
Improper intake cam timing Stuck OCV plunger Check the OCV valve operation using the YDIS. 5-21
Improper intake cam timing Stuck OCV plunger Check the OCV plunger. 5-21
Improper intake cam timing Clogged OCV filter Replace the OCV filter. 10-15
Improper intake cam timing Clogged oil passage Check the oil passage. 2-21
Improper intake cam timing Stuck VCT Replace the VCT assembly. 7-42

Symptom 1: Limited engine speed (below 2000-3000 r/min).

Symptom 2 Cause Checking steps See page
Buzzer comes on. Overheat alert indicator comes on Thermo switch malfunction Measure the thermo switch input voltage. 5-35
Buzzer comes on. Overheat alert indicator comes on Thermo switch malfunction Check the thermo switch for continuity. 5-35
Buzzer comes on. Overheat alert indicator comes on Thermo switch malfunction Check for continuity between the thermo switch and the engine ECM. A-5
Buzzer comes on. Overheat alert indicator comes on Clogged cooling water inlet Check the cooling water inlet. 10-9
Buzzer comes on. Overheat alert indicator comes on Water pump malfunction Check the impeller. 6-17
Buzzer comes on. Overheat alert indicator comes on Water pump malfunction Check the impeller key. 6-17
Buzzer comes on. Overheat alert indicator comes on Water pump malfunction Check the water pump housing. 7-29
Buzzer comes on. Overheat alert indicator comes on Water pump malfunction Check the insert cartridge. 10-4
Buzzer comes on. Overheat alert indicator comes on Water pump malfunction Check the outer plate cartridge. 8-12
Buzzer comes on. Overheat alert indicator comes on Clogged cooling water passage Check the cooling water passage. 2-23
Buzzer comes on. Overheat alert indicator comes on Open PCV Check the PCV. 7-71
Buzzer comes on. Overheat alert indicator comes on Thermostat malfunction Check the thermostat. 7-71
Buzzer comes on. Oil pressure alert indicator comes on. Insufficient engine oil Check the engine oil level. 10-4
Buzzer comes on. Oil pressure alert indicator comes on. Insufficient engine oil Check for engine oil leakage. 2-21
Buzzer comes on. Oil pressure alert indicator comes on. Insufficient engine oil Check the valve stem seals and valves. 7-60
Buzzer comes on. Oil pressure alert indicator comes on. Insufficient engine oil Check the piston rings. 7-91
Buzzer comes on. Oil pressure alert indicator comes on. - Measure the oil pressure. 7-1
Buzzer comes on. Oil pressure alert indicator comes on. Engine oil pressure decrease Check the oil pump. 7-83
Buzzer comes on. Oil pressure alert indicator comes on. Engine oil pressure decrease Check the oil strainer. 9-21
9-36
Buzzer comes on. Oil pressure alert indicator comes on. Engine oil pressure decrease Check the relief valve. 7-79
Buzzer comes on. Oil pressure alert indicator comes on. Engine oil pressure decrease Check the oil passage (power unit and oil pump). 2-21
Buzzer comes on. Oil pressure alert indicator comes on. Engine oil pressure decrease Replace the oil filter. 10-13

Symptom 1: Discharged battery

Symptom 2 Cause Checking steps See page
Low voltage indicator activates on the gauge Battery performance decrease Check the battery capacity and specific gravity. 10-4
Low voltage indicator activates on the gauge Battery performance decrease Check the proper connection of battery cables and terminals. —
Low voltage indicator activates on the gauge Short, open, or loose connection in charging circuit Check the proper connection of the charging circuit and for damage. A-6
Low voltage indicator activates on the gauge Stator assembly malfunction Measure the lighting coil outputpeak voltage. 5-28
Low voltage indicator activates on the gauge Stator assembly malfunction Measure the lighting coil resistance. 5-28
Low voltage indicator activates on the gauge Rectifier/Regulator/lsolator malfunction Measure the Rectifier/Regulator/lsolator output voltage. 5-29
Low voltage indicator activates on the gauge Rectifier/Regulator/lsolator malfunction Check the Rectifier/Regulator/lsolator for continuity. 5-29

Symptom 1: Y-COP lock and unlock do not function

Symptom 2 Cause Checking steps See page
There is an answer back (beep) Y-COP remote control transmitter malfunction Check the button cell battery voltage. -
There is an answer back (beep) Y-COP remote control transmitter malfunction Replace with a spare remote control transmitter. -
There is an answer back (beep) Short, open, or loose connection of the wire harness Check the Y-COP circuit. -

Symptom 1: Y-COP lock and unlock function, but there is no answer-back (beep)

Symptom 2 Cause Checking steps See page
- Buzzer malfunction Check the buzzer. -
- Short, open, or loose connection of the wire harness Measure the buzzer input voltage. -
- Short, open, or loose connection of the wire harness Check the Y-COP circuit. -

Troubleshooting the PTT unit

Troubleshooting consists of the following 3 items:
Symptom 1: Specific trouble conditions
Symptom 2: Trouble conditions of an area or individual part
Cause: Trouble causes of symptom 2
—: Not applicable

Symptom 1: PTT unit does not operate.

Symptom 2 Cause Checking steps See page
PTT relay does not operate Blown fuse Check the fuse. 5-5
PTT relay does not operate PTT switch malfunction Check the PTT switch. 5-49
PTT relay does not operate PTT relay malfunction Check the PTT relay. 5-48
PTT relay does not operate Short, open, or loose connection of the wire harness Measure the PTT switch input voltage. 5-49
PTT relay does not operate Short, open, or loose connection of the wire harness Measure the PTT relay input voltage. 5-48
PTT relay does not operate Short, open, or loose connection of the wire harness Check for continuity between the PTT switch and the PTT relay A-6
PTT relay does not operate Short, open, or loose connection of the wire harness Check for wiring continuity between the PTT switch and the fuse. A-6
PTT motor does not operate PTT motor malfunction Check the PTT motor. 9-66
PTT motor does not operate Short, open, or loose connection of the PTT motor lead Check for wiring continuity between the PTT motor and the PTT relay terminal. A-6
PTT motor does not operate Bent tilt ram or trim ram Check the tilt ram and trim ram. 9-78
PTT motor does not operate Stuck tilt ram or trim ram Disassemble and check the PTT unit. 9-78
PTT fluid pressure does not increase - Measure the PTT fluid pressure 9-61
PTT fluid pressure does not increase Open manual valve Check the manual valve. 9-63
PTT fluid pressure does not increase Insufficient PTT fluid Add sufficient PTT fluid. 10-18
PTT fluid pressure does not increase PTT fluid leakage Check for PTT fluid leakage. 10-18
PTT fluid pressure does not increase Clogged fluid passage Disassemble and check the PTT unit 9-73
9-78
PTT fluid pressure does not increase Clogged fluid passage Check the filter for dirt and obstructions. 9-81
PTT fluid pressure does not increase Clogged fluid passage Check the valves for damage. 9-75
PTT fluid pressure does not increase Clogged fluid passage Check the fluid passages for obstructions. 9-73
9-78
PTT fluid pressure does not increase PTT motor malfunction Check the PTT motor. 9-66
PTT fluid pressure does not increase Gear pump malfunction Check the gear pump assembly. 9-76

Symptom 1: PTT unit does not hold the outboard motor up.

Symptom 2 Cause Checking steps See page
Decrease in PTT fluid pressure in lower chamber of PTT cylinders Open manual valve Check the manual valve. 9-63
Decrease in PTT fluid pressure in lower chamber of PTT cylinders Insufficient PTT fluid Add sufficient PTT fluid. 10-18
Decrease in PTT fluid pressure in lower chamber of PTT cylinders PTT fluid leakage Check for PTT fluid leakage. 10-18
Decrease in PTT fluid pressure in lower chamber of PTT cylinders Clogged or open fluid passage Disassemble and check the PTT unit. 9-73
9-78
Decrease in PTT fluid pressure in lower chamber of PTT cylinders Clogged or open fluid passage Disassemble and check the PTT unit. 9-75
Decrease in PTT fluid pressure in lower chamber of PTT cylinders Clogged or open fluid passage Check the fluid passages for obstructions. 9-73
9-78

Troubleshooting the lower unit

Troubleshooting consists of the following 3 items:
Symptom 1: Specific trouble conditions
Symptom 2: Trouble conditions of an area or individual part
Cause: Trouble causes of symptom 2
—: Not applicable

Symptom 1: Shift mechanism of the forward gear and reverse gear does not operate properly.

Symptom 2 Cause Checking steps See page
- Shift cable is not adjusted properly Adjust the shift cable. 10-7
- Shift rod does not operate properly Check the shift lever operation. 10-6
- Shift rod does not operate properly Check the shift rod for wear. 8-12
- Shift mechanism malfunction (in lower unit) Check the shift rod connection. 8-35
8-36
- Shift mechanism malfunction (in lower unit) Check the dog clutch and related parts. 8-18
- Shift mechanism malfunction (in lower unit) Check the forward gear, reverse gear, and pinion for damage and wear. 8-26
8-18
8-26
Share on social:

Related Products