PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Owner's Manual DF250, DF225, DF200 Operation

Related Products:
Owner's Manual DF250, DF225, DF200 Operation
99011-93J40-03B
Suzuki Marine

Owner's Manual DF250, DF225, DF200 Operation

  1. For the next 1 hour:

Safe boating conditions permitting, operate the engine in gear at 4000 r/min. or at three quarter throttle. Avoid running the engine at full throttle.

  1. Remaining 7 hours:

Safe boating conditions permitting, operate the engine in gear at desired engine speed. You may occasionally use full throttle; how ever do not operate the engine continuously at full throttle for more than 5 minutes at any time.

Running continuously at full throttle for more than 5 minutes at a time during the last 7 hours of break-in operation may cause severe engine damage such as seizure. During the last 7 hours of break-in operation, do not operate at wide open throttle for more than 5 minutes at a time.

OPERATION

BEFORE ATTEMPTING TO START THE ENGINE

  1. Lower the motor into the water.

  2. Make sure that the motor fuel hose and the hose from the boat’s fuel tank are securely attached and clamped.

  1. Make sure the motor is in “NEUTRAL”.

  1. Make sure the lock plate is in place and the emergency stop switch cord is fastened securely to your wrist or appropriate clothing area such as your belt.

Failure to properly attach the emergency stop switch cord or to take proper precautions to help ensure that the emergency stop switch works as intended may result in serious injury or death to the operator or passengers. Always take the following precautions:
• Make sure that the emergency stop switch cord is fastened securely to the operator’s wrist or to an appropriate clothing area (belt etc.). • Ensure that no obstructions impede or restrict emergency stop switch operation. • Be careful not to pull the stop switch cord or knock out the lock plate during normal operation. The motor will stop abruptly, and the loss of forward motion may unexpectedly throw occupants forward.

There is a spare plastic lock plate for temporary use only. Remove it from the cord and place in a safe place on the boat. However, the original cord and lock plate should be replaced as soon as possible.

STARTING THE ENGINE

Exhaust gas contains carbon monoxide, a dangerous gas that is difficult to detect because it is colorless and odorless. Breathing carbon monoxide can cause death or severe injury. Never start the engine or let it run indoors or where there is little or no ventilation.

If the emergency stop switch lock plate is not in position, the starter motor cannot operate.

  1. Squeeze the fuel line priming bulb several times until you feel resistance.

2. Side mount type:

Make sure the warm-up lever is in the fully closed position.

  1. Turn the ignition key to the “ON” position, then observe the monitor-tachometer indication. If nothing abnormal is indicated, then turn the key to the “START” position to start the engine.

![][219760]

If you turn the ignition key to “START” position for more than 5 seconds, the starter system could be damaged. Never turn the ignition key to “START” position for more than 5 seconds.

If the OIL lamp remains lit while operating the outboard, the oil level may be low enough to damage the engine. Stop the engine and check the oil level.

The continuous operating time of the starter motor is set at five seconds. When this time is exceeded, the starter motor will automatically stop. If the motor stops, wait about ten seconds for the motor to cool down and try again.

  1. Warm up the engine for about 5 minutes.

Cooling water check

As soon as the engine starts, water should spray out of the pilot water hole 1, indicating that the water pump and cooling system are working properly. If you notice that water does not spray out of the pilot water hole, stop the engine as soon as possible and consult your authorized Suzuki Marine Dealer.

Never operate your outboard motor when there is no water coming out of the pilot water hole, or severe damage can result. After starting the engine, check to make sure that there is water coming out of the pilot water hole.

Operating the boat when the emergency stop switch is not operating properly can be hazardous. Before starting off, check to make sure that the emergency stop switch operates properly.

SHIFTING AND SPEED CONTROL

Severe engine damage may occur if (a) engine speed is not allowed to return to idle and boat speed is not reduced when shifting from “FORWARD” to “REVERSE” or from “REVERSE” to “FORWARD”, or (b) care is not taken when operating the boat in reverse. Always allow the engine speed to return to idle before shifting. Exercise caution and use minimal speed when operating the boat in reverse. Be sure the handle/ shift lever is in the desired position before accelerating.

If you shift gears when the engine is not running, the shifting mechanism can be damaged. Avoid shifting gears when the engine is not running.

Shifting

To shift into “FORWARD”, squeeze the lock-out lever on the control handle and move the control handle forward to approximate position A, as shown in the illustration.

To shift into “REVERSE”, squeeze the lock-out lever on the control handle and move the control handle rearward to approximate position B, as shown in the illustration.

A detent or notch is present on all Suzuki control boxes to provide a “feel” for positions A, B, and neutral. Always shift quickly and firmly from neutral to position A or B to prevent abnormal wear on the gear and clutch engagement surfaces.

Top mount type Not equipped with a lock-out lever. Exercise care when selecting neutral position.

Speed control

To increase speed after you have shifted into gear, continue moving the control handle for ward or rearward.

Since the same handle is used for shifting and speed control it is possible to move the handle past the detent and engage the throttle. This can cause the boat to move suddenly resulting in personal injury or property damage. You must be careful not to move the control handle too far forward or rearward when shifting.

STOPPING THE ENGINE

When it is necessary to stop the engine in an emergency, pull the emergency stop switch lock plate out of the emergency stop switch by pulling the emergency stop switch cord.

To stop the engine:

  1. Shift into “NEUTRAL”.

  2. After operating at full throttle, cool off the engine a few minutes by allowing it to idle or troll at low speed.

  1. Turn the ignition key to the “OFF” position. Always leave the ignition key in the “OFF” position when the motor is not running, or the battery can discharge.

If the ignition key is left ON when the engine is not running, the battery will discharge. Always turn the ignition key OFF when the engine is not running.

Unauthorized use of your boat could lead to an accident or damage to your boat. To prevent unauthorized use of your boat, be sure to remove the key and emergency stop switch lock plate when the boat is unattended.

  1. After stopping the engine, disconnect the fuel line from the outboard motor if there is a fuel connector.

If you leave the motor stopped for a long period of time with the fuel line connected , fuel can leak out. Disconnect the fuel line from fuel tank, if there is a fuel connector, whenever you leave the motor stopped for a long period of time

  1. Turn the air-vent screw on the fuel tank cap clockwise to shut the vent (if equipped )

To make sure that the emergency stop switch operates properly, stop the engine occasionally by pulling out the lock plate, while operating the engine at idling speed.

MOORING

The motor should be tilted up out of the water when you moor the boat in shallow water or if the motor will not be used for some time, to protect it from damage by underwater obstacles at low tide or corrosion from salt water.

Refer to the TILT LEVER section for details on how to tilt up the motor.

Improperly securing your boat may cause damage to your boat or motor, or other property damage. Do not allow your motor to rub against quay walls, piers or other boats when the boat is tied up.

OPERATION IN SHALLOW WATER

When operating your boat in shallow water, it may be necessary to tilt the motor higher than the normal trim angle. When you tilt the motor beyond the normal trim angle, however, you should only operate the boat at slow speeds. After returning to deep water, be sure to lower the motor to the normal trim angle.

To tilt the motor higher than the normal trim angle, use the Power Trim and Tilt switch.

When the motor is beyond the maximum trim position, the swivel bracket will not have side support from the clamp bracket and the tilt system will be unable to cushion the engine if the lower unit strikes an obstruction. This could lead to occupant injury. In addition, beyond the maximum trim position, the water intake holes may be above the water line, which can result in severe engine damage from overheating. Do not operate the engine above 1500 r/min or operate the boat in a planning attitude with the engine beyond the maximum trim position.

If the motor hits bottom, serious damage can occur. Do not allow the motor to hit bottom. If the motor does strike bottom, inspect it immediately for damage.

OPERATION IN SALT WATER

After operating the motor in salt water, you should flush the water passages with clean, fresh water as outlined in the FLUSHING THE WATER PASSAGES section. If you do not flush the water passages, salt can corrode the motor and shorten its life.

OPERATION IN FREEZING WEATHER

When operating your outboard motor in freezing temperatures, you should keep the lower unit submerged in the water at all times.

When taking motor out of the water, stand it up in a vertical position until the cooling system drains completely.

If you leave your outboard motor out of the water in freezing temperatures with water still in the cooling system, the water can freeze and expand, causing severe damage to the motor. When your outboard is in the water in freezing temperatures, keep the lower unit submerged in the water at all times. When the motor is stored out of the water in freezing temperatures stand it up in the vertical position so that the cooling system drains completely

Share on social:

Related Products