PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

OE 2012 Evinrude E-TEC Installation & Predelivery Guide (P-N 5008815) - Technical Specifications Remote Oil Tank Installation (V4-V6) [Boat Rigging]

Related Products:
OE 2012 Evinrude E-TEC Installation & Predelivery Guide (P-N 5008815) - Technical Specifications Remote Oil Tank Installation (V4-V6) [Boat Rigging]
5008815
BRP Marine

Location

Consider the installation location of the oil tank carefully. The oil tank is vented to the atmosphere. To avoid serious powerhead damage, be sure the oil tank is installed in a location that does not allow constant exposure to sunlight, rain, bilge water or spray.

Select a mounting location that provides:

  • A solid place to mount the tank
  • A dry location that prevents exposure to rain or spraying water
  • Access for adding oil
  • Access to oil-primer bulb
  • Interference-free hose and wire routing to outboard.

If necessary, the oil tank can be mounted further from the outboard than the supplied hoses and harness allow. The maximum length of oil supply hose that can be fitted to the oil tank is 25 ft. (7.6 m).

Do not add hose to an existing oil supply hose.

If the oil tank requires a longer oil supply hose:

  • Oil supply hose between the primer bulb and outboard must be replaced with one continuous length of 1/4 in. (6.4 mm) I.D. hose.
  • Maximum length of hose is 25 ft. (7.6 m).
  • Replacement hose must be designated for fuel or oil use and approved for marine use.
  • Extend wiring harness with 16 gauge AWG wire.
  • Protect connections with heat shrink tube.
  • Maintain wire color and polarity when extending harness.

An appropriately sized battery box may be used to conceal and protect the oil tank, if desired.

Be sure box includes drain holes so it does not fill with water and contaminate oil.

Mounting

Place tank in selected position. Mark one line under groove in tank bottom and lines at each end of tank.

  1. Center line of oil tank
  2. Ends of tank

Make sure hole locations provide enough clearance for fastening screws. Screws should not contact or penetrate hull.

Place floor bracket on center line between end lines. Use the inner bracket holes as guides to drill two 5/32 in. (4 mm) pilot holes.

3 GALLON (11.4 L) TANK
Place rods into floor bracket and secure floor bracket with lag bolts.

  1. Rods
  2. Lag bolts

Place oil tank onto floor bracket. Assemble crossbar onto hook rods, install flat washers and locknuts. Tighten locknuts to securely hold tank.

  1. Crossbar

1.8 GALLON TANK
Place rods into floor bracket and secure floor bracket with lag bolts.

  1. Rods
  2. Lag bolts

Place oil tank onto floor bracket. If cover is not pre-assembled, route oil supply hose and harness through the cover and position cover on the oil tank. Attach spring-loaded rods to cover.

Oil Tank Profiles

Remote Oil Fill Kit (Optional)

The remote oil fill kit (P/N 176461) provides a deck-mounted fill tube, cap, a tank-mounted tube, and nut that replace the original oil tank cap assembly.

Installation Recommendations
• Select a location on the deck of the boat that is above the oil tank fill cap.
• Select a deck location which allows the required length of 1½ in. I.D. fill hose to route as directly and as vertically as possible.
• Avoid inappropriate hose routings that could distort the fill tube or tank tube.
• Refer to installation instructions provided with remote oil fill kit.

A slanted area of the deck will allow water to drain away from the fill and is best suited for the installation.

Additional Items Required
• 1½ in. I.D. fill hose cut to required length. Fill hose (P/N 123956) is available in 25 ft. (7.6 m) lengths.
• Two corrosion resistant 2 in. (50 mm) hose clamps.

Share on social:

Related Products