Step 1: EXPLODED DIAGRAM

Step 2: REMOVAL AND INSTALLATION CHART
| Step | Procedure/Part name | Q'ty | Service points |
|---|---|---|---|
| PROPELLER SHAFT AND REVERSE GEAR REMOVAL | Follow the left "Step" for removal. | ||
| Gear oil | Refer to the "LOWER UNIT" section in chapter 3. | ||
| Propeller | Refer to the "LOWER UNIT REMOVAL" section. | ||
| 1 | Bolt (with washer | 2 | 6 x 20 mm |
| 2 | Propeller shaft housing assembly | 1 | |
| 3 | Plate washer | 1 | |
| 4 | Propeller shaft | 1 | |
| 5 | Cross pin ring | 1 | |
| 6 | Cross pin | 1 | NOTE : By pushing the shift plunger, bring the cross pin hole in the dog clutch with the hole in the shift slider. |
| 7 | Dog clutch | 1 | NOTE : Install the clutch with "F" mark toward the forward gear side. |
| 8 | Shift plunger | 1 | |
| 9 | Spring | 1 | |
| PROPELLER SHAFT HOUSING DISASSEMBLY | |||
| (1) | O-ring | 1 | |
| (2) | O-ring | 1 | |
| (3) | Reverse gear | 1 | |
| (4) | Reverse gear shim | * | |
| (5) | Ball bearing | 1 | |
| (6) | Oil-seal | 2 | |
| (7) | Needle housing | 1 | |
| (8) | Propeller Shaft housing | 1 | |
| Reverse the removal steps for installation. |
*: As required
Step 3: SERVICE POINTS


Propeller shaft housing removal
- Remove:
- Propeller shaft housing assembly
Bearing housing puller :
YB-06234..........(1)
90890-06503 ......(3)
Universal puller :
YB-06117..........(2)
Stopper guide plate :
90890-06501 ......(4)
Center bolt :
90890-06504.......(5)
[A] For USA and CANADA
[B] Except for USA and CANADA

Propeller shaft housing disassembly
- Remove:
- Ball bearing (1)
Slide hammer set :
YB-06096........(2)
Stopper guide plate :
90890-06501.....(3)
Bearing puller :
90890-06535.....(4)
Stopper guide stand :
90890-06538.....(5)
[A] For USA and CANADA
[b] Except for USA and CANADA

- Remove:
- Needle bearing
Driver rod : YB-06071/90890-06604
Needle bearing attachment : YB-06081/90890-06616
Reverse gear inspection
- Inspect:
- Tooth
- Dog
Wear/Damage ➝ Replace
Bearing inspection
- Inspect:
- Bearing
Pitting/Rumbling ➝ Replace.
- Bearing
Propeller shaft housing inspection
- Clean:
- Propeller shaft housing
Use a soft brush and solvent
- Propeller shaft housing
- Inspect:
- Propeller shaft housing
Crack/Damage ➝ Replace.
- Propeller shaft housing
Dog clutch inspection
- Inspect:
- Dog clutch
Wear/Damage ➝ Replace.
- Dog clutch
Propeller shaft inspection
- Inspect:
- Propeller shaft
Wear/Damage ➝ Replace
- Propeller shaft

Propeller shaft housing assembly
- Install:
- Needle bearing
Depth (a) : 0 mm (0 in)
Driver rod : YB-06071/90890-06604
Needle bearing attachment : YB-06081/90890-06616

- Install:
- Oil seal
Depth (a) : 3.0 ~ 3.5 mm (0.12 ~ 0.14 in)
Oil seal installer : YB-06168
Driver rod : YB-06071
- Install:
- Ball bearing
Bearing installer : YB-06015
Driver rod : YB-06071
