PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Lower Unit [Shimming] [2013]

Related Products:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 2003 - 2005 200hp All
Yamaha International 2003 - 2005 225hp All
Yamaha International 2003 - 2005 200hp All
Yamaha Outboard 2003 - 2005 225hp All

Lower Unit [Shimming] [2013]
LIT-18616-02-76
Yamaha Marine

Lower unit (regular rotation model)

No. Part name Q’ty Remarks
1 Lower unit 1
2 Plate 1
3 Rubber seal 1
4 Check screw 1
5 Gasket 2 Not reusable
6 Dowel pin 2
7 Bolt 7 M10 x 45 mm
8 Drain screw 1
9 Grommet 1
10 Bolt 1 M10 x 44 mm
11 Bolt 1 M10 x 70 mm
12 Spacer 1
13 Washer 1
14 Propeller 1
15 Washer 1
16 Washer 1
17 Cotter pin 1 Not reusable
18 Propeller nut 1
19 Trim tab 1

No. Part name Q’ty Remarks
1 Shift rod 1
2 Oil seal 1 Not reusable
3 Oil seal housing 1
4 O-ring 1 Not reusable
3.1 x 70.6 mm
5 Spring 1
6 Circlip 1
7 Bolt 3 M6 x 20 mm
8 Seal 1
9 Woodruff key 1
10 Bolt 4 M8 x 45 mm
11 Cover 1
12 Seal 1
13 Water pump housing 1
14 O-ring 1 Not reusable
2.5 x 42 mm
15 Insert cartridge 1
16 O-ring 1 Not reusable
2.5 x 91.5 mm
17 Collar 1
18 Spacer 1
19 Washer 2
20 Wave washer 1
21 Impeller 1
22 Outer plate cartridge 1
23 Gasket 1 Not reusable
24 Dowel pin 2

Removing the lower unit

  1. Drain the gear oil. For draining procedures, see Chapter 3, “Changing the gear oil.”

  2. Set the gearshift to the neutral position, and place a block of wood between the anti-cavitation plate and propeller to keep the propeller from turning, and then remove the propeller nut and propeller.

WARNING
Do not hold the propeller with your hands when loosening or tightening it. Be sure to disconnect the battery cables from the batteries and the engine stop lanyard switch. Put a block of wood between the anti-cavitation plate and propeller to keep the propeller from turning.

  1. Mark the trim tab (1) at the area shown, and then remove it.

  2. Loosen the bolts, and then remove the lower unit from the upper case.

NOTE:
Check that there is no oil on the spline and check it for wear.

Removing the water pump and shift rod

  1. Remove the water pump assembly and shift rod assembly (1).

Checking the water pump and shift rod

  1. Check the water pump housing for deformation. Replace if necessary.

  1. Check the impeller (1) and insert cartridge (2) for cracks or wear. Replace if necessary.

  1. Check the Woodruff key (3) and the groove (a) on the drive shaft for wear. Replace if necessary.

  1. Check the shift rod for cracks or wear. Replace if necessary.

Share on social:

Related Products