PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Fuel System [Carburetor] [2002]

Related Products:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1997 - 2003 15hp All
Yamaha Outboard 1997 - 2003 9.9hp All
Yamaha International 2001 - 2003 9.9hp All
Yamaha International 2001 - 2003 15hp All

Fuel System [Carburetor] [2002]
LIT-18616-01-65
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q'ty Service points
CARBURETOR DISASSEMBLY Follow the left "Step" for removal
Carburetor assembly Refer to the "CARBURETOR REMOVAL"section in chapter 4.
1 Drain screw 1
2 Washer 1
3 Screw (with washer) 4 4x14 mm
4 Float chamber 1
5 Float chamber packing 1
6 Screw 1
7 Arm pin 1
8 Float 1
9 Clip 1
10 Needle valve 1
11 Cap 1
12 Pilot jet 1
13 Main jet 1
14 Main nozzle 1
15 Screw (with washer) 4 4 x 10 mm
16 Plate 1
17 Packing 1
18 Stopping screw 1
19 Spring 1
20 Pilot adjusting screw 1
21 Spring 1
22 Carburetor body 1
FUEL PUMP DISASSEMBLY
(1) Screw (with washer) 4
(2) Pump cover 1
(3) Diaphragm 1
(4) Pump body 1
(5) Screw 2
(6) Seat valve 2
(7) Nut 2
(8) Diaphragm 1
(9) Diaphragm gasket 1
Reverse the removal steps for installation.

SERVICE POINTS

NOTE:
Do not use steelwire for cleaning the jets as this may enlarge the jet diameters and seriously affect performance.

Carburetor inspection

  1. Inspect:
    • Carburetor body
      Crack/Damage ➝ Replace.
      Contamination ➝ Clean
  2. Inspect:
    • Pilot screw
      Bend/Wear ➝ Replace.
  3. Inspect:
    • Main jet
    • Pilot jet
    • Main nozzle
      Contamination ➝ Replace

  1. Inspect:
    • Needle valve
      Grooved wear ➝ Replace.
  2. Inspect:
    • Float
      Crack/Damage ➝ Replace.

Fuel pump inspection

  1. Inspect:
    • Body
      Crack/Leak/Damage ➝ Replace.
  2. Inspect:
    • Seat valve
      Crack/Distortion ➝ Replace.
  3. Inspect:
    • Diaphragm
    Damage ➝ Replace.

Carburetor assembly

  1. Install:
    • Needle valve
    • Float (1)
    • Float pin (2)
    • Screw (3)

NOTE:

  • The float pin should be fit in the slit the carburetor and locked with the screw.
  • After installing, check the smooth movement of the float.
  1. Measure:
    • Float height (a)
      Out of specification ➝ Replace.

Float height (a) : 14.0 ± 1.5 mm (0.55 ± 0.06 in)

NOTE:

  • The float should be resting on the needle valve, but not compressing the needle valve.
  • Take measurement at the end surface of the float opposite to its pivoted side.

  1. Adjust:
    • Pilot screw

Adjustment steps:

  • Screw in the pilot screw until it is lightly seated.
  • Back out by the specified number of turns.

Pilot screw : 1-1/2 ± 1/4 (turns out)

Share on social:

Related Products