PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Fuel System [Carburetor] [1996]

Related Products:

Applicable Models

Model group Year Model Serial
Yamaha Outboard 1996 150hp All
Yamaha Outboard 1996 175hp All
Yamaha Outboard 1996 200hp All
Yamaha Outboard 1996 225hp All
Yamaha Outboard 1996 250hp All

Fuel System [Carburetor] [1996]
LIT-18616-01-41
Yamaha Marine

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step Procedure/Part name Q’ty Service points
CARBURETOR DISASSEMBLY Follow the left "Step" for removal
Carburetor assembly Refer to "CARBURETOR REMOVAL" section.
1 Drain screw 2
2 Gasket 2
3 Main jet 2
4 Pilot jet plug 2
5 Gasket 2
6 Pilot jet 2
7 Screw 4
8 Float chamber 1
9 Float chamber gasket 1
10 Arm pin 2
11 Float assembly 2
12 Clip 2
13 Needle valve 2
14 Screw 1
15 Air vent cover 1
16 Plug screw 2
17 Gasket 2
18 Pilot screw 2
19 Spring 2
20 Plug screw 1
21 Gasket 1
22 Pilot air jet 2
23 Throttle adjust screw 1 middle carburetor
24 Spring 1
25 Carburetor body 1
Reverse the removal steps for installation.

SERVICE POINTS

Do not use steel wire for cleaning the jets as this may enlarge the jet diameters and seriously affect performance

Carburetor inspection

  1. Inspect:
  • Carburetor body
    Crack/Damage -> Replace.
    Contamination -> Clean.
  1. Inspect:
  • Pilot screw
    Bend/Wear -> Replace.
  1. Inspect:
  • Main jet
  • Pilot jet
  • Main air jet
  • Pilot air jet
  • Main nozzle
    Contamination ->Replace.
  1. Inspect:
  • Needle valve
    Grooved wear -> Replace.
  1. Inspect:
  • Float
    Crack/Damage -> Replace.

Carburetor assembly

  1. Install:
  • Needle valve
  • Float
  • Float pin
  • Screw

NOTE:
After installing, check the smooth movement of the float.

  1. Measure:
  • Float height @
    Out of specification -> Replace.

Float height: 16.0 ± 0.5 mm (0.63 ± 0.02 in)

NOTE:

  • The float should be resting on the needle valve, without compressing it.
  • Measure at the end of the float, opposite to its pivoting end.
  1. Adjust:
  • Pilot screw

Adjustment steps:

  • Screw in the pilot screw until it is lightly seated.
  • Back out by the specified number of turns.

Pilot screw (turns out):
150: 1 ± 1/4
S150: 1-1/4± 1/4
P150:
S: 1-9/16 ± 1/4,
P: 1-1/16 ± 1/4
175: 1-1/16 ± 1/4
S175: 1-1/8± 1/4
P175:
S: 1-5/8 ±1/4,
P: 1-1/8 ± 1/4
200: 1-1/8 ±1/4
S200:
S: 1-1/8 ±1/4,
P: 5/8 ± 1/4
P200, 225:
S: 1-1/4 ± 1/4,
P: 3/4±1/4

Share on social:

Related Products