PREPARE FOR WINTER: 10-50% discount on all OEM parts!

Unless prohibited by manufacturer. Does not include aftermarket or Crowley Marine branded products. Priced as marked.

Our warehouses are closed on Thursday and Friday, November 26th and 27th. Happy Thanksgiving!

Search Over 1 Million OEM Parts
Easy-to-use  parts diagrams Best price  guarantee Expert  live support 50+ years  of serving boaters Huge selection of OEM parts  -  from 1950 to 2026 Most parts in stock  -  Same day fulfillment
Most parts in stock- Same day fulfillment

Bracket Unit [Power Trim And Tilt Motor] [2004]

Related Products:

Applicable Models

Model group Year Model Serial
Yamaha International 2004 60hp All
Yamaha Outboard 2004 60hp All

Bracket Unit [Power Trim And Tilt Motor] [2004]
LIT-18616-FT-60
Yamaha Marine

Power trim and tilt motor


S62Y7890R

Tightening torques Tightening torques Tightening torques Tightening torques
No Part name Q’ty Remarks Stage N•m kgf•m ft•lb
1 Screw 3 M5 x 20 mm
2 Yoke 1
3 O-ring 1 Not Reusable
4 Armature 1
5 Bushing 1
6 Screw 2 M4 x 12 mm
7 Wire lead 1
8 Brush 2 1
9 Brush 1 1
10 Brush holder 1
11 Circuit breaker 1
12 Brush spring 2
13 PTT motor base 1
14 Oil seal 1 Not Reusable

Checking the power trim and tilt motor

  1. Check the commutator for dirt or foreign substances. Clean with #600 grit sand paper if necessary.

S62Y7900

  1. Check the commutator undercut for dirt or foreign substances. Clean with com pressed air if necessary.

  2. Measure the commutator diameter (a). Replace if out of specification.

S62Y7910

Commutator diameter limit (a): 21 mm (0.83 in)

  1. Check the armature coil for continuity. Replace if out of specifications.

S62Y7920

S62Y7925

Armature coil continuity
Commutator segments (b) Continuity
Segment-laminations (c) No continuity
Segment-shaft (d) No continuity
  1. Check the circuit breaker for continuity. Replace if there is no continuity.

S62Y7930

  1. Measure the brush length. Replace if out of specification.

S62Y79940

Brush length limit 3.5 mm (0.14 in)

  1. Check the base for cracks or damage. Replace if necessary.
  1. Check the bushing (1) for damage or wear. Replace if necessary.

S62Y7950

Assembling the power trim and tilt motor

  1. Install the oil seal (1) and the bushing (2) into the motor base (3) as shown.

S62Y7960

  1. Attach the circuit breaker (4) onto brush 2 (5) together with the brush holder (8) and connect the wire lead (7).

S62Y7975

  1. Install the springs (8) into the motor base, then the brush holder into the motor base together with the brushes and circuit breaker.

  2. Install the armature (9), O-ring (10), and yoke (11).

S62Y7985

Installing the power trim and tilt

  1. Fully tilt the outboard up, and then sup port it with the tilt stop lever (1).

S62Y7990

WARNING

After tilting up the outboard, be sure to support it with the tilt stop lever.
Otherwise, the outboard could suddenly lower if the power trim and tilt unit should lose fluid pressure.

2.Install the shaft (2) and bolts (3) onto both clamp brackets together with the power trim and tilt/hydro tilt (4).

3.Install the tilt ram upper end into the swivel bracket with the shaft (5) and cir clip(s) (6).

  1. Install the tilt pin (7).

S62Y7A10

Power trim and tilt electrical system

(1) Power trim and tilt motor
(2) Power trim and tilt relay
(3) Power trim and tilt switch
(4) Fuse
(5) Battery
(6) Trim sensor

B : Black
G : Green
L : Blue
Lg : Light green
P : Pink
R : Red
Sb : Sky blue

Share on social:

Related Products