0My cart

My cart

Cart is empty
0My cart
Crowley Marine: serving boaters for over 40 years Crowley Marine: serving boaters for over 40 years
Most parts in stock Same day fulfillment
$3.95 shipping on all orders*
Low Price Guarantee
9.6 Pilot logo
0My cart

Stop Switch Kit P/N 583975

Crowley Marine

Safety Considerations

These instructions will alter you to certain things you should do very carefully. If you don't, you could...

  • hurt yourself or bystanders
  • hurt boat operator, passengers
  • damage the machinery

Safety symbol, , appears next to information important to prevent you and others from being hurt.

Note symbol, Note, appears next to information important to keep machinery from being damaged.

IMPORTANT: The important safeguards and instructions appearing in these directions cannot cover all possible conditions or situations that occur. The person following these directions must use common sense, caution and care.

Product Reference & Illustration

When reference is made to brand name, product or specific tool, an equivalent product may be used in place of the referred to product. Substitute products used must have equivalent characteristics, including type, strength, and material. Incorrect substitution may result in product malfunction and possible injury to the operator and/or passengers.

All photographs and illustrations used may not necessarily depict actual models or equipment, but are intended only for reference. Specifications used are based on the latest product information available at the time of publication.
 

Preface

This stop switch kit will service all Johnson® and Evinrude® outboards with a stop switch in the tiller handle.

The installation of this kit requires special tools and involves procedures described in detail in the Service Manual for your product. If you do not have and do not wish to purchase the tools and literature required, have this kit installed by your Evinrude/Johnson Dealer.
 

Step 1. Prepare for Installation

Read all the instructions before starting work.

[1]
Review contents of kit:

Ref. Name of Part Qty.
1 Switch Assembly 1
2 Pin Terminal 1
3 Socket Terminal 1
4 Ring Terminal 1
5 Grease 1

Collect necessary tools and supplies:

Common hand tools
Wire cutter-stripper-crimping pliers
Amphenol removal and installation tools
Twist-Grip™ Remover P/N 390767
 

Step 2. Remove Old Switch

Refer to Midsection - Steering Handle Servicing in Service Manual for disassembly procedures.
 

Step 3. Attach Terminals

[2]
Compare wire lengths and terminal ends of old switch and new switch (1). If wires on new switch are longer cut them to length of old switch wires. Push end of braided sleeve off wires and cut the same amount off the sleeve (A) so sleeve remains 8 inches shorter than wires. Heat the cut end of sleeve to prevent fraying. If either terminal is different that terminal must be removed and the correct one installed.

NOTE: Braided sleeve cannot be PULLED off wires. Braided sleeve must be PUSHED off and on wires to move it.

[1] [3]
If either terminal must be replaced, or the leads shortened, strip about 3/16 in. (5 mm) of insulation from wire. select terminal from kit that is the same as on the old switch wire.

[1] [3]
Attach the Amphenol pin (2) and/or socket (3) with the Crimping Pliers (A) as required to duplicate the original terminal configuration.

[1]
Attach the ring terminal (4), if required, with a universal type crimping pliers.

If you are not sure you have a good mechanical and electrical connection on any of the terminals, solder the terminals to the wires.
 

Step 4. Install Switch

Refer to Midsection - Steering Handle Servicing in Service Manual for reassembly procedures.

[4]
Lubricate the switch shoulder between the four tabs (B) (surface under the tabs) before installing the grip over the stop switch on the steering handle. Use the supplied lubricant (5).

[5]
Starting with the stop switch assembled in the handle, screw idle stop switch all the way out (counterclockwise).

[6]
Push braided sleeve against switch and wrap leads around throttle cable, using only two evenly spaced and flat spirals. Secure with tape as shown.

[7]
If used, apply spiral wrap starting at the twist grip.
 

Step 5. Test switch

Start motor and push stop button to stop motor. If motor does not stop repair as required.

Related Products

0583975 - KIT AY,IDL STOP SW

Flat $3.95 Shipping on ALL parts orders

We offer shipping flat $3.95 shipping on ALL parts orders. (Complete Engines, Lower Units and Sterndrives excluded). In addition orders over $89 have reduced cost express shipping available in checkout.

shipping map shipping map legend

You can get a rough idea of standard transit times from the map above.

Our boats now have their own website!

You can find all of our new and used boats at www.crowleyboats.com

Proceed to Crowley Boats

Please bookmark (crtl+d) www.crowleyboats.com for future reference.